Preboot-etherboot-server ( IP address, any: Default: any) Since etherboot accepts IP addresses from any BOOTP/DHCP server, use preboot-etherboot-server to start etherboot only when address is received from specified Netinstall server. This feature can be disabled from the RouterOS menu or by resetting the BIOS. The preboot-etherboot configuration is stored in the BIOS, downgrading RouterOS to older versions will not disable it. Preboot-etherboot ( timeout interval 1s.9s Default: d isabled) Values depend on the model, to see available options, hit the button in RouterOS version 6 or the button in RouterOS version 7 button on the keyboard at this prompt This option allows changing the memory data rate of the device. Memory-data-rate ( depends on the model Default: depends on model) This option allows changing the memory frequency of the device. Memory-frequency ( depends on model Default: depends on model) In case your modem is not being recognized after a soft reboot, then you might need to add a delay before the USB port is initialized Used for mPCIe modems with RB9xx series devices only Init-delay ( timeout interval 0s.9s Default: ) yes - backup loader will be used always.So that you don't have to boot the device with a pushed reset button (which loads the backup loader), you can use this setting to load it every time This is only useful if the main loader has become corrupted somehow and cannot be fixed. Note that in some serial terminal programs, it is impossible to use the Delete key to enter the setup - in this case, it might be possible to do this with the Backspace keyįorce-backup-booter ( yes | no Default: no) Useful when the serial console prints out symbols during the boot process and goes into RouterBOOT menu by itself. Which key will cause the BIOS to enter configuration mode during boot delay. When the CPU is in suspend mode, it consumes less power, but in low-temperature conditions, it is recommended to choose a regular mode, so that the overall system temperature would be higherĮnable-jumper-reset ( yes | no Default: yes)ĭisable this to avoid accidental setting reset via the onboard jumperĮnter-setup-on ( any-key | delete-key Default: any-key) Most OSs use HLT instruction during the CPU idle cycle. Whether to enter CPU suspend mode in HTL instruction. Values depend on the model, to see available options, hit the button in RouterOS version 6 or the button in RouterOS version 7 on the keyboard at this promptĬpu-mode ( power-save | regular Default: power-save) This option allows for changing the CPU frequency of the device. dhpc - used for OpenWRT and possibly other OSĬpu-frequency ( depends on model Default: depends on model).bootp - the default option for booting RouterOS.Using the serial console, press any key while the device is booting and choose "o" then "1" and "x"īoot-os ( router-os |swos Default: router-os)Ĭhanges the booting operating system for CRS3xx series switchesīoot-protocol ( bootp |dhcp. Using the serial console, w hen the device is booting up, keep pressing CTRL+E on your keyboard until the device shows that it is trying bootp protocolģ. Press the Reset button and power on your device (wait until "USR" led is blinking then stable "On" and when the "USR" led is "Off" - release the Reset button) - the device is booting in bootp mode to reinstall RouterOS using Netinstall.Ģ. There are several ways to put your device into Etherboot mode depending on the device you are using:ġ. If you see that the upgrade-firmware value is bigger than current firmware, you simply need to perform the upgrade command, accept it with y and then reboot with /system rebootĮtherboot mode is a special state for a MikroTik device that allows you to reinstall your device using Netinstall. It is recommended to keep this version upgraded. RouterBOOT upgrades usually include minor improvements to overall RouterBOARD operation. In either case, the newest found version will be shown here. The file can either be included via a recent RouterOS upgrade or an FWF file that has been manually uploaded to the router. This line shows if a new RouterBOOT file has been found in the device. RouterOS upgrades also include new RouterBOOT version files, but they have to be applied manually. The serial number of this particular device. Whether this is a MikroTik RouterBOARD device. The version of the RouterBOOT loader the particular device was manufactured with.įirmware type that is used on the particular device. Not to be confused with RouterOS operating system version. The version of the RouterBOOT loader is currently in use.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |